|
 |
 |
|
Back to Product Line |
|
|
|
|
|
|
In A Class By Itself!
|
|
The 7035
is 10 years of proven technology that has set the
standard in integrated towing and recovery units,
combined into an all-new package with many new and
enhanced features. The recovery boom has been
totally redesigned to provide increased reach and
greater hydraulic power to tackle the toughest
lifting and recovery jobs. For difficult-to-tow
vehicles, the underlift enhancements include a
fabricated 2nd and 3rd stage stinger to provide
additional reach, along with increased positive and
negative tilt for ease of hook-up and improved
stinger clearance. The newly-designed tailboard
incorporates diagonally-opposed outriggers and dual
position feet to provide stability and holding power
on a variety of surfaces. Contact your local
Century distributor and find out how your heavy-duty
towing and recovery business can benefit from the
industry leader, the Century 7035.
|
|
|
CENTURY 7035 -
STANDARD FEATURES |
|
156" C.B. Body,
96" Wide with Fenderettes |
Modular Body
with 4 Tool Compartments Per Side |
|
Lumber Box Under
Tool Compartments (Left & Right Side) |
Tool Compartment
Lights, Shelves and Chain Racks |
|
2 Storage
Compartments over Wheelwell |
Manual Controls
(All Functions) Driver Side |
|
Lift For Storage
Racks, Passenger & Drivers Side |
Mud Flaps |
|
Manual Boom
Controls on Passenger Side |
Air Free Spools
and Air Tensioners |
|
Dual Hydraulic
Pump |
Light Pylon with
Full Running Lights |
|
Pressure Gauges |
Recessed Air and
Electrical Hookups |
|
Diagonal Rear
Jacks with Multi Position Feet |
1 Set of 5/8"
Hook Adapters |
|
1 Set of 1/2" x
14' Safety Chains in Rear Pockets |
8 Sets of Lift
Forks |
|
1 Set Pivot
Spring Adapters |
Federal Standard
108 Lighting |
|
Power Network
Electrical System, 15-Function Wired and Wireless Control
and 2 Twelve Function Panels |
|
|
CENTURY 7035 -
OPTIONAL EQUIPMENT |
|
Airshift PTO |
108" C.B. Body
or 204" C.B. Body |
|
Tri-Axle Body |
Tunnel Box 24"
(180" C.B. or Longer Body Only) |
|
Aluminum Modular
Tool Boxes, 156" CB, 180" CB, 204" CB |
Composite
Aerodynamic Light Pylon with Marker Lights |
|
2 Rectangular
Work Lights (Upper) |
Tail Gate
Underlift Control Panel |
|
Aluminum
Dress-Up Kit |
Convenience
Group (Rails & Steps) |
|
Turn Signal
Strobe Kits |
Light Bar |
|
Grater Blade
Attachment |
Off Set Fork
Holder |
|
Chain Hook Slide
Adapter |
Fork Riser
Bracket |
|
Pintle Hook
Attachments |
5th Wheel Plate
(Requires Pintle Hook Attachment) |
|
Engine Data
Information Center |
Snatch Block (8"
Sheave, each) |
|
Heavy-Duty Truck
Wheel Lift |
Wide Load Light
Bar |
|
Installation |
|
|
CENTURY 7035 - WRECKER
SPECIFICATIONS |
|
RECOVERY BOOM
|
REACH / CAPACITY |
|
Lift Cylinders
Power Retracted 30° (SAE)
Extended 30° (SAE)
Maximum Extension
Maximum Angle
Maximum Hook Height - Spades Up |
6" bore
70,000 lbs.
22,000 lbs.
130"
40°
249" |
|
 |
|
WINCH SPECIFICATIONS |
|
|
Planetary
Winches
Cable
Air Cable Tensioners
Air Free Spools |
(2) 35,000 lbs.
6 x 37 200' x 3/4" IWRC X-Plow
|
|
UNDERLIFT
SPECIFICATIONS |
|
|
Full Retracted
Fully Extended At Third Stage
Positive Tilt
Negative Tilt
CTR of Rear Axle to Rear Bumper
Estimated Shipping Weight |
54" / 35,000
lbs.
129" / 16,000 lbs.
10°
10°
38.3"
14,220 lbs. |
|
CENTURY 7035 -
CHASSIS
RECOMMENDATIONS |
|
Tandem 40,000
lb. rear axle capacity. Minimum RBM (resisting bending
moment) for each frame rail is 2,250,000 in./lb., minimum
GVW (gross vehicle weight) is 53,200 lbs.
All specifications are minimums, heavier specifications may
be required depending on chassis and equipment weights.
Minimum C.B. (cab to bogie) dimension is 156 inches. The
minimum frame length behind the center line of the rear axle
is 40 inches. The outside frame rails of chassis extending
behind cab must be free of fuel tanks, air tanks, battery
boxes, etc.
Note: Specifications subject to change without notice.
All ratings specified are based on structural factors only,
not
vehicle capacities or capabilities. |
