|
 |
 |
|
Back to
Product Line
|
|
|
CHALLENGER
HAS THE DOMINATING FORCE
to provide you
with a heavy duty integrated towing
and recovery unit designed for
efficient weight transfer to
maximize you (single axle) and the
CH-32 (tandem axle) are the new
force to take on the challenge of
your tough assignments with features
that include 25,000 lb. planetary
winches with air free spool and air
tensioners, diagonal rear spades
with multi-position feet and a 3
stage underlift with a 16,000 lbs.
of lift capacity at an extension of
113".
|
|
|
CHALLENGER CH-31 / CH-32 SERIES - STANDARD
FEATURES |
|
CH-31 - 156" C.A. Steel
Modular Body
CH-32 - 156" C.B. Aluminum
Modular Body |
96" Wide Body with Fenderettes and
4 Forward Tool Compartments |
|
Dual Side by Side Elevation Cylinders with
Counter Balance Valve |
Tool compartment Lights, Shelves and Chain
Racks |
|
2 Storage Compartments over Wheelwell |
Lift Fork Storage Racks, Passenger and
Drivers Side |
|
Manual Boom Controls on Passenger Side |
Manual Controls (All Functions) Drivers Side |
|
Dual Hydraulic Pump |
Mud Flaps |
|
Pressure Gauges |
Air Free Spools and Air Cable Tensioners |
|
Diagonal Rear Jacks With Multi-Position Feet |
Light Pylon with Full Running Lights |
|
1 Set of 1/2" of 14' Safety Chains in Rear
Pockets |
Recessed Air And Electrical Hookups |
|
8 Sets of Lift Forks |
1 Set 5/8" Hook Adapters |
|
Remote Hand Held Lanyard (8 Function) |
Federal Standard #108 Lighting |
|
Switch Panel (9 Function) |
|
|
CHALLENGER CH-31 / CH-32 SERIES - OPTIONAL
EQUIPMENT |
|
CH-31 - 182" C.A. Steel or
156" or 182" C.A. Aluminum Body |
|
CH-32 - 180" or 204" C.B.
Aluminum Body |
|
24" Tunnel Box
(requires minimum 182" C.A. 180" or 204"
C.B.) |
Composite Aerodynamic Light Pylon with
Marker Lights |
|
Air Shift PTO |
Tailgate Underlift Control Panel |
|
2 Rectangular Work Lights (Upper) |
Convenience Group (Rails & Steps) |
|
Aluminum Dress Up Kit |
Light Bar |
|
Whelen Turn Signal Strobe Kits |
Composite Pylon Wings |
|
Grater Blade Attachment |
Off Set Fork Holder |
|
Chain Hook Slide Adapter |
Fork Riser Bracket |
|
Winch and Boom Controls on Remote |
Rear Vision Camera |
|
Engine Data Information Center |
Snatch Block (8" Sheave, each) |
|
Heavy-Duty Truck Wheel Lift |
Wide Load Light Bar |
|
Pintle Hook Attachment |
Installation |
|
5th Wheel Plate
(Requires Pintle Hook Attachment) |
Power Network Electrical System, 8-Function
Wired and Wireless Controller and 2 Twelve
Function Panels |
|
Many other popular Challenger options |
|
|
CHALLENGER CH-31 / CH-32 SERIES - WRECKER
SPECIFICATIONS |
|
Recovery Boom |
Reach/Capacity |
|
Lift Cylinders
Power CH-31 Retracted 30° (SAE)
CH-32 Retracted 30°
(SAE)
Extended 30° (SAE)
Maximum Extension
Maximum Angle
Maximum Hook Height, Spades Up
Reach Past Tailgate at 3° |
5 1/2" bore
50,000 lbs.
60,000 lbs.
16,000 lbs.
120"
39°
219"
101" |
|
 |
|
CHALLENGER CH-31 / CH-32 SERIES - UNDERLIFT
SPECIFICATIONS |
|
Underlift |
|
|
Fully Retracted
Fully Extended at Third Stage
CTR of Rear Axle to Rear Bumper
Estimated Shipping Weight |
49" / 35,000 lbs.
113" / 16,000 lbs.
38.3"
CH-31 12,200 lbs.
CH-32 12,060 lbs. |
|
CHALLENGER CH-31 / CH-32 SERIES - WINCH
SPECIFICATIONS |
|
Winch Specifications |
|
|
Planetary Winches
Cable
Air Cable Tensioners
Air Free Spools |
(2) 25,000 lbs.
200' x 5/8"
|
|
CHALLENGER
CH-31 / CH-32 SERIES
- CHASSIS
RECOMMENDATIONS |
|
Minimum RBM (resisting
bending moment) for each frame rail is
2,250,000 in./lb. The minimum frame length
behind the center line of the rear axle is
40 inches. The outside frame rails of
chassis extending behind cab must be free of
fuel tanks, air tanks, battery boxes, etc.
All specifications are minimums, heavier
specifications may be required depending on
chassis and equipment weights. The CH-31
requires a minimum 156" C.A. with a GVW of
33,000 lbs. The CH-32 requires a minimum
C.B. of 156" C.T. with a GVW of 53,200 lbs.
Note: Specifications subject to
change without notice. All ratings
specified are based on structural factors
only, not vehicle capacities or
capabilities. |
