|
|
|
|
The Ultimate
Recovery Machine |
|
Strength . . . Reach . . . Durability . . .
|
|
Challenger has
engineered the finest technology into these
features and combined them with a rotating
boom, features include a two-stage boom with
extended reach, 360° of boom rotation;
forward outriggers; and Challenger's sleek
body design with modular tool compartments. |
|
CHALLENGER 8808 & 9909 ROTATOR SERIES -
STANDARD FEATURES |
|
3 stage
hydraulic pump |
Dual, variable
speed hydraulic planetary winches |
|
250 ft. winch
cable, each winch |
Cable tensioners |
|
360° boom end
swivels |
Boom angle
indicator gauge |
|
Rigid torsional
resistant mounting frame |
Power boom
elevation and retraction |
|
Safety Chains |
House locks -
secures wrecker in stored position 180°
apart |
|
96" wide heavy
duty body with flat floor |
Nylatron bearing
boom slide pads |
|
108° C.B.
Modular Body |
Lubrication
fittings on all shafts and other moving
parts |
|
Rear D Rings |
2 stage power
boom extension with counterbalance valve |
|
Pressure gauges |
Dual control
stations |
|
Mud flaps |
2 D-Rings
mounted on outer and inner recovery booms |
|
Deluxe switch
panel |
Federal standard
# 108 lighting |
|
Fenderettes |
Wiring harness
in loom with junction box |
|
Excellent
control valve location for service |
360° Boom
Rotation |
|
Hydraulic
reservoir with rubber isolated mounts |
Spring loaded
tool compartment door returns |
|
Front outriggers
with self storage |
Air operated
winch clutch release |
|
Rear hydraulic
extendable outriggers |
Hydraulic pump
with suction oil flow shut off valve |
|
Load holding
valves on boom elevation, boom extension,
rear spade extension and front outrigger
down and up |
Hydraulic
reservoir has removable clean out cover with
tank drain and oil level sight gauge |
|
CHALLENGER 8808 & 9909 ROTATOR SERIES -
OPTIONAL EQUIPMENT |
|
SDU/3 underlift
with power tilt |
Truck hitch with
hook-up chains |
|
Spotlights |
Convenience
group |
|
Snatch blocks |
Side mounted "D"
rings |
|
Rear mounted
Drag Winches |
Tool compartment
lights |
|
Wrecker special
light |
Work light below
tailgate |
|
Wrecker lanyard
control |
Air & Electrical
Hookups |
|
Aluminum Body |
Air Shift PTO |
|
Winch bucket
mounted light pylon with electrical
collector ring for 360 degree rotation |
Aluminum dress
up package |
|
CHALLENGER
8808 & 9909 ROTATOR SERIES
- SPECIFICATIONS
|
|
|
8808
|
9909
|
|
BOOM
|
|
|
|
Basic
structural rating
TEMA
|
Retracted
Extended |
100,000
lbs.
34,000 lbs. |
140,000
lbs.
50,000 lbs. |
|
Reach
past tailgate at 0"
|
Retracted
Extended |
26"
182" |
24"
180" |
|
Maximum
working height at maximum elevation
|
32'
|
30'
|
|
Range of
elevation |
0° - 57°
|
0° - 52°
|
|
Boom
Rotation |
360°
|
360°
|
|
FRAME WINCH
|
|
|
|
Type
|
Planetary |
Planetary |
|
Capacity
per winch |
50,000
lbs. |
60,000
lbs. |
|
Cable
size |
3/4" x
250' |
7/8" x
250' |
|
|
CHALLENGER 8808 & 9909 ROTATOR SERIES -
CHASSIS
RECOMMENDATIONS |
|
Tri-Axle Chassis
is recommended: however, Tandem Chassis can
be accommodated. Consult factory for
further details. |
|
Minimum Front
Axle GAWR
Minimum Rear Axle GAWR
Minimum C.B. (Cab to Bogie) Dimension
Min. Frame Length behind Center Line of Rear
Axle
RBM (in./lbs.) - Model 8808
RBM (in./lbs.) - Model 9909 |
20,000 lbs.
46,000 lbs.
180"
40"
3.5 mil.
4.0 mil. |
|
All
recommendations are minimums. Heavier
specifications may be required depending on
Chassis
and Equipment weights. |
|
Specified
minimum C.B. is for standard length body and
provides adequate towing capabilities.
Longer C.B. chassis can be accommodated at
additional cost. Consult factory for any
non-standard C.B. chassis. |
|
The outside
frame rails of chassis extending behind cab
must be free of fuel tanks, air tanks,
battery boxes, exhaust tacks, etc. |
|
Note: Specifications subject to change
without notice. All ratings specified are
based on structural factors only, not
vehicle capacities or capabilities. |
